ZEGA D470A DTH blasthole drilling rig
Three main types of holes are drilled in surface mining
1. Blast holes
Hole diameter 115 – 229 mm (4½ – 9 in)
Hole depth 6 – 20 m (18 – 60 ft)
− Blast holes are production holes and will be filled with explosives
− Drilling accuracy is important to obtain good and even distribution of the explosives in the rock
− This will optimize fragmentation and facilitate further handling such as mucking, hauling and crushing
2.Buffer holes
Hole diameter 115 – 152 mm (4½ – 6 in)
Hole depth 6 – 20 m (18 – 60 ft)
3.Perimeter holes (pre-split)
Hole diameter 115 – 152 mm (4½ – 6 in)
Hole depth 6 – 20 m (18 – 60 ft)
− Pre-split and buffer holes are used for wall control
− This method reduces the amount of waist rock excavation and also the risk of rock fall from pit walls
− Usually smaller hole diameter than blast holes to carry less explosives
Technical parameter
| Model | ZEGA D470A | Hole range | Φ138 - 165 mm |
| Suitable DTH hammer sizes | 5 inch | Drill pipe handling capacity | 4+1 |
| Drill pipe outer diameter | Φ114 mm | Drill pipe length | 7m |
| Hole depth | 35m | Rotation speed | 0-105 rpm |
| Max. torque | 4310 N.m | Rod handling | 4+1 |
|
Engine |
|||
| Engine model | Caterpillar C11 | Rated power | 287 kw |
| Emission standard | Tier IIIA | Fuel tank capacity | 600L |
|
Air compressor- Zega |
|||
| Maximum working pressure | 24 bar | Rated F.A.D | 20 m³/min(706cfm) |
|
Feed beam |
|||
| Hydraulic motor | Hydraulic cylinder +steel wire | Feed length | 9100 mm |
| Travel length | 6500 mm | Feed extension | 1300 mm |
| Maximum feeding rate | 0.88m/s | Max. Feed force | 34.5KN |
| Max pull up force | 67.6 KN | Tramming speed | 3km/h |
| Traction force | 117.7 KN | Hill climbing ability | 25° |
| Track frame oscillation angle | 士10° | Ground clearance | 420 mm |
| Weight | 23000 kg | Dimension | 11280*2500*3530 mm |
Application
Quarrying aggregate – limestone
Application demands
− A wide spread of customers in this application, from small quarries serviced by contract drillers to big operations with own personnel and equipment
Blast hole drilling
Hole diameter 90 – 205 mm (3½” – 8”)
Hole depth 10 – 30m
− Many quarries are located close to urban areas and environmental regulations put restrictions on drilling parameters
− Hole accuracy is important
− Noise restrictions give DTH drilling an advantage
Related products
-
ZGYX-430 Separated Blast hole drilling rig smal...
Technical parameter as below Specifications of Diesel Engine Drill Rig Model E Model Engine Model ZGYX-430 Yuchai ZGYX-425/ZGYX-430 Yuchai YC4DK-80 @58 kW ZGYX-430-1(with dust collector) Yuc ZGYX-425-1(with dust collector)/ZGYX-430-1 Yuchai YC4DK-100@73.5 KW General specification Model ZGYX-420 ZGYX-425 ZGYX-430 Drill pipe 76mm *3m 76mm*3m 76mm*3m Hole range 90-140 mm 110-152 mm 110-165 mm Tor...
-
FY-200/FY-300 tracked pneumatic deep well drill...
Advantages The rig can be used for drilling on different formations with a maximum diameter of up to 350 mm. The rig adopts new hydraulic technology, which is equipped with high-torque hydraulic motor rotation and large-diameter hydraulic cylinder propulsion. The famous engine provides power for the hydraulic system, two-stage air filter and the intake air design of the compressed air to extend the service life of the diesel eng...
-
ZEGA D355 Blast hole drilling rig with cummins ...
-
ZGYX-416F Separated Blast hole drilling rig sma...
Technical parameter as below Specifications of Diesel Engine Drill Rig Model Engine Model ZGYX-416 Yuchai YC4DK80 58kW ZGYX-416-1(with dust collector) Yuchai YC4DK80 58kW General specification Model ZGYX-410 ZGYX-412 ZGYX-416 Drill pipe 60mm*2m 60mm *2m 60mm *3m Hole range Φ 90 – 110 mm Φ 90 – 110 mm Φ90-127mm Torque ( Max. ) 1650 N.m 1650 N.m 1950 N...
-
ZGYX-420B Separated Blast hole drilling rig sma...
Technical parameter as below Specifications of Diesel Engine Drill Rig Model Engine Model Model Engine Model ZGYX-420B Yuchai YC4DK-80 @58 kW ZGYX-425/ZGYX-430 Yuchai YC4DK-80 @58 kW ZGYX-420B-1(with dust collector) Yuchai YC4DK-100@73.5 KW ZGYX-425-1(with dust collector)/ZGYX-430-1 Yuchai YC4DK-100@73.5 KW General specification Model ZGYX-420B/ZGYX420B-1 ZGYX-425 ZGYX-430 Drill pipe 76mm *3m 76mm*3m...
-
ZEGA D545 Blast hole drilling rig with cummins ...
Features ■The standard configuration is two-meter drill pipe, model with dry dust collector and enhanced traveling motor. ■The rotary head is driven by a cycloidal gear motor, which has low failure rate, small size and large torque, and is suitable for a larger range of rock drilling apertures. ■The self-developed high-performance wet air filter is combined with the dry air filter to form a three-stage air filter system to bette...